4WD Power Wheels Go Kart Gets Suspension! 228cc Bronco Kart Pt. 6

  Shikime 180,520


3 muaj më parë

We're working on our Ford Bronco power wheels go kart with a Tillotson 228cc racing engine, and we're getting close to completion! In today's episode, we built upper and lower control arms for the front suspension, and crucially figure out and fabricate Ackerman steering, all while retaining our four wheel drive plans. Finally, we mount the front shocks and place the body on the chassis, and we get a very good view of what the finished 4wd go kart will look like!
Thanks for Watching!
Facebook: goo.gl/VR6mh2
Instagram: goo.gl/PqOIo3
-----------------Go Power Sports Parts Used in Today’s Video----------------
Tell them CarsandCameras sent you at checkout:
Tillotson 228 engine: bit.ly/2zQCG3w
Super 30 series torque converter (with Juggernaut): bit.ly/3ahxWlD
Live axle kit: bit.ly/359NJ1J
420 racing chain: bit.ly/2l6zklT
4x4 live axle hub: bit.ly/2WZFW2c
8 inch diameter wheels: call for availability
Racing seat: bit.ly/2x8tYZG
8” brake disc: bit.ly/2XUbIkp
Engine mount: bit.ly/3bCM8VO
HD shocks: bit.ly/3a8FTHU
Reverse Kit: bit.ly/3ixLNqK
Steering: bit.ly/305HwSN (call for availability)
Steering wheel: bit.ly/2YYHH1A
Springer spindle: bit.ly/2sowOv3
420 split sprockets: bit.ly/3kFMeRx
Go Power Sports: goo.gl/c2Tz6o
Get $100 off any Langmuir Systems Crossfire CNC plasma table using this link, or use code CARSANDCAMERAS at checkout: store.langmuirsystems.com/discount/CARSANDCAMERAS
NEW MERCH: www.cars-cameras.com/
Equipment we use: www.amazon.com/shop/carsandcameras
The following video features activities performed in controlled environments by knowledgeable persons. DO NOT attempt to duplicate, re-create, or perform the same or similar activities at home, as personal injury or property damage may result. CARS AND CAMERAS, the persons shown in this video and ANY CONTRIBUTOR, ARE NOT LIABLE FOR ANY such injury or damage. ALL CARSANDCAMERAS CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.

Cars and Cameras makes no representation about the sufficiency of any safety precautions and equipment used in this video.

FrustratedBaboon 2 muaj më parë
Isn't that amazing that you hold a piece of metal in the air and after a few zaps you have on solid metal piece that is stronger than anything else.
Motorsports4Christ_Jon 2 muaj më parë
Let me know when you are ready to race my 700cc Bronco Powerwheels
Hellwithpots 3 muaj më parë
Y’all don’t understand front suspension geometry at all lol do some research
Delicious DeBlair
Delicious DeBlair 3 muaj më parë
Why did you not bend parts for the front control arms for clearance so that they still mount at the strongest point possible!? ~( ,m,)~
REDKILLER lol 3 muaj më parë
anyone else know wtf there talking about?
GATOSGARAGE 3 muaj më parë
oh man loved it until i saw the engine you are putting ,come on man!!,all the trouble to use that engine???///sorry i gotta dislike.
Tashaud Dripping
Tashaud Dripping 3 muaj më parë
Put trailer wheels and tires on it
Brody Wiening
Brody Wiening 3 muaj më parë
You guys are my insperation you have taught me so much in the year that ive been watching you. Thank you
Fredrick Hawthorne
Fredrick Hawthorne 3 muaj më parë
Paint the frame red and white. It’ll be very patriotic.
Donald Isaacs
Donald Isaacs 3 muaj më parë
Please build a golf cart!!! You guys are awesome, please
TheMadWookiee 3 muaj më parë
Bend the front tube around the shock
Uncle Stumpys One-legged Band
Uncle Stumpys One-legged Band 3 muaj më parë
Go get it Ike and John!!
oliver grandbois
oliver grandbois 3 muaj më parë
Ike say; oups!! John say; what? Ike say; front suspension body... Front suspension...
Matthew Lynch
Matthew Lynch 3 muaj më parë
Been following for a while. Any chance you could send a pic of the new cars and cameras rat rod shirt as it isn’t on your site yet. This a message from an extremely avid follower in Australia. You both do an outstanding job and can’t wait for more.. How do we get merchandise in Australia ? Keep up the great work👍
Joes welding
Joes welding 3 muaj më parë
'Grind hard plumbing' how to build a slow version
Billy Hellboy
Billy Hellboy 3 muaj më parë
Who told you to precut boi u made of money is ya boi well you are going have to fix it boi
Fawkyooo 3 muaj më parë
This is just something to take a look at your G-Code Software is messing up. It should be cutting the inner circle out [Bolt holes] Before it cuts the outer perimeter. That way your bolt holes are always the same on every plate and the plate doesn't shift while cutting the bolt holes.
cdoublejj 3 muaj më parë
how about a big ass block of nylon with 2 long holes to guide the chain? (sacrificial i guess)
cdoublejj 3 muaj më parë
@Obilwe wufuh Mubufu Oulou you going to need some super tiny ass gears and bearings
Paul mc duff
Paul mc duff 3 muaj më parë
Junkyard Diggs has bought me to your channel, just starting my epic task of watching everything you have done love what I've seen so far, thanks guys, proper engineering at its best
michael blacktree
michael blacktree 3 muaj më parë
John: We'll have to make another compromise. Ike's Facial Expression: I'm dying inside. 😜
Fishing Squad
Fishing Squad 3 muaj më parë
You should make a Dooley go kart
Stephan Blake
Stephan Blake 3 muaj më parë
Question on a carb jet. Fairly new to the mini bike gang. Bought a predator 420cc from Harbor Freight. It came with 2 additional jets. One is a 95 labeled (6000-8000ft) and the other is a 97 labeled as (3000-6000ft). I did not take out the one already in the carb so i have no idea what that one is. So the question of my question is, is a performance jet any different for the stage one kit to one of these extras i can swap out instead of buying a jet?
JKemme Sends
JKemme Sends 3 muaj më parë
Put a wheel on the hubs and line both hubs up with a long piece of c channel
Nickalie Hulmer
Nickalie Hulmer 3 muaj më parë
u guys might need a psychiatrist too much math give me a headace
Ripriot RC
Ripriot RC 3 muaj më parë
Looks great guys
conspiracy files
conspiracy files 3 muaj më parë
Do more things with forced induction
Mark Pikas
Mark Pikas 3 muaj më parë
You guys are so much better at this than you were a few years ago (I don't know, whenever I started watching you and annoying you with "you needed to do it like..." comments), but if you're going to be building vehicles with independent suspensions and going 40, 60, 80... mph in them you really need to get a better handle on suspension geometry. 2 major things in this one: - caster- about 5-10* is the typical dedicated drag car/dragster, 3-6* for a fast road race car, and 2-4* for your average street car. Everything that I've seen you build, including the rail, I would just set it at 5* and make sure it's the same side to side loaded. - Ackerman- where did you get the idea that you need a rear steer linkage to have Ackerman? Front steer is generally the preferred design for most applications for multiple reasons, and you can get ackerman with it. The only reason that you see rear steer at all is really packaging reasons.
Salty Ballsack
Salty Ballsack 3 muaj më parë
2 guys or 8 girls
justin watch
justin watch 3 muaj më parë
You know what you should do.. You should cut that thing up and make it into a unicycle for a monkey and just plain start over. You guys got great engineering ideas but the execution is all wrong. So just go back, take a few hits off the bong and let's see what you really got.
Kyle Spivey
Kyle Spivey 3 muaj më parë
did u just say grocery cart?!
Aysha Lamiya
Aysha Lamiya 3 muaj më parë
Hi I'm from kerala (god zone country) I'm your big fan your videos great. Please watch my video
Brayden Goins
Brayden Goins 3 muaj më parë
Yall should take the Ducarti 900cc to the drag strip!!!
tshegofatso 3 muaj më parë
Can I get this we have now much money please
Trial N' ERROR
Trial N' ERROR 3 muaj më parë
This entire thing is an engineering disaster (coming form a channel that is also full of engineering disasters).
Resuppliied 3 muaj më parë
anybody know what type of big bore kit to buy for a taotao 125cc 4 stroke automatic engine
Drew 003
Drew 003 3 muaj më parë
You guys need a ct90
Shawn Lasswell
Shawn Lasswell 3 muaj më parë
Getting closer
BassmanDave 3 muaj më parë
With how y'all are mounting the front shocks, I think the first really big bump you hit will likely taco your lower A arm. That's a weak mounting point for the shock. Just a thought. :-)
Yuval Philipson
Yuval Philipson 3 muaj më parë
You guys should consider using spherical bearings with housings that you stake the bearings into for your A-Arms. You have all of your suspension rod ends in bending which makes them very prone to failure
Kyle Clark
Kyle Clark 3 muaj më parë
I'm having the hardest time securing the throttle cable without putting too much pressure on the cable inside. Any advice from anyone? Edit: predator 212 is the engine. Straight from go power sports.
g0ldensample21 3 muaj më parë
Is this going to be to short?
Alexander Hackworth
Alexander Hackworth 3 muaj më parë
I've got an idea Make a amphibious go kart (APC)
John Hill
John Hill 3 muaj më parë
Great video guys. 3am and the Old Man enjoying with my coffee☕. John really glad your Dad told me about you two. 🚙😎💗
Mister Pimlott
Mister Pimlott 3 muaj më parë
Have not watched these guys in 4 or 5 yrs, I love that the content has not changed
Woods 3 muaj më parë
Hey if you guys do another mini bike I would like to see you guys try and make the tubular frame the exhaust pipe like have the exhaust run thru the entire frame just because plz upvote so they can see
Finish Dude
Finish Dude 3 muaj më parë
Waiting for the end result
Brian Bauer
Brian Bauer 3 muaj më parë
I think it would awesome if y'all could get youre hands on a 1988 yamaha dt50 cause I have one and I would like to know more about it
Adam 3 muaj më parë
would love to be able to order a hat and sweater. if shipping to Canada was available. any suggestions on shipping availability
Ervin Goertzen
Ervin Goertzen 3 muaj më parë
Bad idea to mount the shock like that , too close to center
Craig Grim
Craig Grim 3 muaj më parë
Wish you could squeeze a lawnmower differential in the front but 👍
wildman510 3 muaj më parë
Already abandoned the estate lol?
Milly Amp
Milly Amp 3 muaj më parë
ATV, scooter, universal wiring harness that might be useful alpost.info/mine/nZbU3pSunWeqomg/video
Justin Dee
Justin Dee 3 muaj më parë
Put a Yamaha blaster motor on something
slim Jim
slim Jim 3 muaj më parë
Fearless Fosdick
Fearless Fosdick 3 muaj më parë
Ackerman steering - alpost.info/mine/n7ywspXLmp-0iJc/video
Bob Tierney
Bob Tierney 3 muaj më parë
The closer you put the bottom of your coil-over to the center of the truck the softer the suspension will be. You may need to move the bottom closer to the wheel. Think of it as a lever which it is.
Clay KN4NIL 3 muaj më parë
If the front chain was to jump off of the sprocket, and somehow lock up the front axles, wouldn't it throw you over the steering wheel and cartwheel? Need some sort of bicycle sprocket that can freewheel forward. Just a thought.
ik04 3 muaj më parë
It's called steering axis inclination and you must have some. Without it the vehicle will wander and diverge from straight ahead while driving.
Brayden Miller
Brayden Miller 3 muaj më parë
Do your mug welders use gas?
Mickey West
Mickey West 3 muaj më parë
I didn't realize I asked question on the old video, so I try again. I was wondering how your going to steer this machine with solid front axle?
Deonte 2x
Deonte 2x 3 muaj më parë
Should put a bigger cc motor in it like @grindhard plumbing would be sick
Nirinium 3 muaj më parë
Using that chop saw right next to all that race fuel :)
J and M tv
J and M tv 3 muaj më parë
you should show all your go karts and mini bike builds
Shredxcam22 3 muaj më parë
Get real shocks with a know spring rate... calculate the leverage against the shock and the angle. Then get the weight of the buggy and order the correct stuff ?! And quit using go china sports to get junk parts.
G1MP NA5A 3 muaj më parë
Daniel Roach
Daniel Roach 3 muaj më parë
Cant wait to see this thing go!!
Dan Jim
Dan Jim 3 muaj më parë
Pretty sure it's an old Mercedes 4wd that had a coil spring that was bent around the front cv axle . Pretty wild looking
Toby Dyes
Toby Dyes 3 muaj më parë
You went more backwards and forwards this episode
Toby Dyes
Toby Dyes 3 muaj më parë
Somebody's gaining some weight
Sean Binyamin
Sean Binyamin 3 muaj më parë
link for the shaft that drive the front wheels?
josh Sampson
josh Sampson 3 muaj më parë
use pushrod suspension and a heavy duty mountain bike shock they are shork ,but the design of pushrod suspension allows you to get travel out of them and mount them where there is more room
thr0ttl3j0ck3y 3 muaj më parë
The powerwheels builds are cool, I can't wait to see the restomod pedal car scene blow up. Bet we'll see some scale straight sixes.
Jason E
Jason E 3 muaj më parë
caster = camber???
Gavin O
Gavin O 3 muaj më parë
I wanna see a 250 two stroke in one of these
Klayton Worley
Klayton Worley 3 muaj më parë
I have a question can i make my belt driven go kart into a chain driven go kart
Kurt 3 muaj më parë
If you change to centrifugal clutch, chain and rear sprocket why not?
Random adventures with Ezra
Random adventures with Ezra 3 muaj më parë
The detail is unbelievable
Katelyn Stoesz
Katelyn Stoesz 3 muaj më parë
rear shocks are not correct
craig engelman
craig engelman 3 muaj më parë
please stop you have no clue . just follow the directions you where given because you are way to stupid and when you try to explain it shows the people who do this for a living are laughing . not much longer and it will be hi its jon and dumbass and today we are in the hospital from multipul barrol rolls and snaping or necks !
Adam McLaughlin
Adam McLaughlin 3 muaj më parë
4wd with mixed tire width? Well I came here for different!
Theodore DuGranrut
Theodore DuGranrut 3 muaj më parë
By the looks of things You all are learning in the best way possible with the long version documented, hopefully there is a condensed version on the side with cold hard facts on what you have learned for future generations. When studying those two engineering architects "Isaac and John" Your first book "Crash & learn" Central California watching
therealracer135 3 muaj më parë
C&C: We're going to build this into a rock crawler, speed isn't our aim here Also C&C: We're gonna get it to go 40mph or more
Tony Mac
Tony Mac 3 muaj më parë
I love all of your projects but this one has been driving me crazy! Can’t wait to see the finished product! Great content Fellas, keep ‘em coming, please?!?
Benjamin Evans
Benjamin Evans 3 muaj më parë
8 wheeler!!!!
Benjamin Evans
Benjamin Evans 3 muaj më parë
Hey comment guys, I recently took the governor in my go kart, and changed the carburetor. My go kart moves by itself. Does anybody know what the problem is?
Benjamin Evans
Benjamin Evans 3 muaj më parë
@therealracer135 thank you I’ll try it
therealracer135 3 muaj më parë
You need to solidly mount the linkage on the carburetor which the governor arm attached to, and turn the idle speed down. Watch some of their early episodes and they show you what to do.
dooman700 3 muaj më parë
You guys send Gopowersports too many customers? Wonder why they dropped the discount to your viewers?
Miko 3 muaj më parë
Look into a plastic welder you could widen the body with one.
Moatheboss Hamdan
Moatheboss Hamdan 3 muaj më parë
how many times have you said tight?
URT Paranormal
URT Paranormal 3 muaj më parë
2:00 throwing sparks at the race fuel
X8_Dev 3 muaj më parë
You guys have no idea how Eager I am to see this kart fully finished. Not sure if this is normal but I feel that I am more excited then I should Be. Keep up the great content
keith bieghler
keith bieghler 3 muaj më parë
Why are you guys making it so small ugh its annoying if you stretch the frame almost all ur issues would be solved. Not trying to be rude its just silly ur making it so hard on yourself.
Brad Huey
Brad Huey 3 muaj më parë
Can't wait til it's done. 👍👍👍
WRENCH g 3 muaj më parë
Man you guys just blow my mind! Why do you guys INSIST on using those Weak Ass shocks all the time! Ugh! Guys I promise you'll never use those cheap ones again after using a cheap Chinese MODERN STYLE
Blayden_1n 3 muaj më parë
What kind of welding is this?
Paul DesFosses
Paul DesFosses 3 muaj më parë
So glad the project was not scrapped, you had me worried for a while
GT1Man 3 muaj më parë
You could not find worse shocks if you tried than those go power trash ones, and flying in the face of physics and correct design philosophy is going to go great for that front suspension. Here's hoping no one gets hurt.
Nick W
Nick W 3 muaj më parë
John! Haircut hippie!! 🤣🤣🤣 jk keep up the awesome videos guys!
Markus Seppälä
Markus Seppälä 3 muaj më parë
"We're still in the testing purposes only stage" Hah you're always in that stage.
ian builds
ian builds 3 muaj më parë
Ackerman can be made up for in the center... it's wierd to do it on a forward facing setup but it's easy just opposite rearward facing steering.. u want your center pitman arm to be triangle shaped and cross the tie rods over/under each other so the tie rods would have to be longest possible as opposed to short if it was rear facing... Any research down the go kart steering rabbit hole should get u an idea of what I mean.. realistically any good Ackerman does will be immediately thwarted by the lack of diff and other improper geometries conspiring against u.. I think the king pin placement will be fine on this but only because the cvs are so overbuilt and the scale is so small...
ian builds
ian builds 3 muaj më parë
In so many words, "it'll be fine"
Diji 3 muaj më parë
Next up, minicrawler!
L Haulins
L Haulins 3 muaj më parë
U boys looked like u smoked your lunch.😂 Great progress on the Bronco.👍
Tayna x Flori Mumajesi x Cricket - Magdalena
Friends Entertainment
Shikime 4,2 mln
Venera Lumani, Lind Islami - Me ty (Official Video)
Venera&Lind Official
Shikime 664 mijë
Shikime 7 mln
go kart eje casero completo facil  3/4
4X4 Ford Bronco Power Wheels Go Kart Pt. 2
Shikime 188 mijë
Honda ATC 70 Restoration | Restored 140cc 3 Wheeler!
Power Wheels DIY Go Kart | All-wheel Drive
Exigent Films
Shikime 9 mijë
Honda CBR 600 buggy build part 1
rather B welding
Shikime 867 mijë
Tayna x Flori Mumajesi x Cricket - Magdalena
Friends Entertainment
Shikime 4,2 mln
Venera Lumani, Lind Islami - Me ty (Official Video)
Venera&Lind Official
Shikime 664 mijë
Shikime 7 mln